Lufft WS301 Multi-Parameter Weather Sensor
Features
- Integrated Kipp & Zonen CMP 3 pyranometer for solar radiation measurements
- Easily mounts to 2" diameter pipe with integrated bracket mount & U-bolts
- SDI-12 output for integration with NexSens and other data loggers
- Free ground shipping
- Expedited repair and warranty service
- Lifetime technical support
- More
Overview
The Lufft family of multi-parameter weather sensors offer a cost-effective, compact alternative for the acquisition of a variety of measurement parameters on land- and buoy-based weather stations. Depending on the model, each sensor will measure a different combination of weather parameters to meet a wide variety of applications. The Lufft WS301 Multi-Parameter Weather Sensor simultaneously measures air temperature, humidity, pressure and solar radiation in a compact platform with ventilated housing.
Air Temperature & Humidity
Temperature is measured using a highly accurate NTC-resistor, while humidity is measured using a capacitive humidity sensor. Both sensors are located in a ventilated radiation shield to reduce the effects of solar radiation.
Pressure
Absolute air pressure is measured using a built-in MEMS sensor. The relative air pressure referenced to sea level is calculated using the barometric formula with the aid of the local altitude, which is user-configurable on the equipment.
Solar Radiation
The pyranometer is intended for shortwave global solar radiation measurements in the spectral range from 300 to 2800nm. The thermopile sensor construction measures the solar energy that is received from the total solar spectrum and the whole hemisphere. The output is expressed in Watts per square meter.
- Air Temperature
- Principle: NTC
- Measuring Range: -50 to +60 C
- Resolution: 0.1 C (-20 to +50 C); otherwise 0.2 C
- Accuracy: +/-0.2 C (-20 to +50 C); otherwise +/-0.5 C
- Units: C; F
- Humidity
- Principle: Capacitive
- Measuring Range: 0 to 100% RH
- Resolution: 0.1% RH
- Accuracy: +/-2% RH
- Units: % RH; g/m3; g/kg
- Pressure
- Principle: Capacitive
- Measuring Range: 300 to 1200hPa
- Resolution: 0.1hPa
- Accuracy: +/-1.5hPa
- Unit: hPa
- Radiation
- Response Time (95%): 18s
- Non-Stability (change/year): ±1%
- Non-Linearity (0 to 1,000 W/m2): ±2.5%
- Directional Error (at 80° with 1,000 W/m2): ±20 W/m2
- Temperature Dependence of Sensitivity: ±5% (–10 to +40° C)
- Tilt Error (at 1000 W/m2): ±3%
- Spectral Range (50% points): 300 to 2,800 nm
- Measuring Range: 1400 W/m2
- Technical Data
- Interface: SDI-12, Modbus
- Operating Temperature: -50 to +60 C
- Operating Humidity: 0 to 100% RH
- Included Cable Length: 10m
- (1) WS301 Multi-Parameter Weather Sensor
- (1) 10m sensor cable
- (1) Operations manual
In The News
Data-Driven Decisions: Tracking Sediment during the Klamath Dam Removal
The largest dam removal in U.S. history, the deconstruction of the Klamath Dam is slated to begin this summer. The project includes four dams along the Klamath River with the first and smallest dam, Copco #2, scheduled for removal first. As each of the dams are torn down, scientists and consultants will keep a close eye on the state of the Klamath River downstream to assess the impact of undamming the river. 
 
Shawn Hinz, managing partner and environmental toxicologist with Gravity Consulting , has been involved with the Klamath Dam project for over a decade. Hinz was a part of these earlier steps, representing the academic stakeholder position as a graduate student sitting on a board of other stakeholders.
Read MoreFrom the Tap: Source Water Monitoring for Public Health
In regions with historically secure access to clean drinking water, few think about the work that goes into ensuring that the water they fill their cups with is safe. In reality, millions of dollars are invested in the infrastructure, equipment and teams involved in converting source water into drinking water. 
 
While all the work that goes into providing clean water often goes unnoticed, analysts like Michele Gilkerson, a water research analyst with the City of Columbus Division of Water, know exactly how much goes into securing safe water for millions of people. 
 
Gilkerson started with Battelle Memorial Institute in 1991 in their water ecology section. There, she saw how interesting source water monitoring could be, even though it isn’t often spotlighted in the environmental sector.
Read MoreChoosing the Right Water Quality Monitoring Systems Is Crucial for Stantec Inc.
Data is king when it comes to water quality monitoring. It is not merely the type of data being collected that matters but also how that data is stored, processed and presented. When Joseph Kamalesh, a project manager with Stantec Consulting Services Inc. , needs to find the right equipment for large client-based projects, he knows to keep these factors in mind. 
 
Joseph has a background in water quality and water flow monitoring instrumentation, which he continues to focus on at Stantec. During college and his early career, Joseph gained experience with water instrumentation, consisting primarily of on-site wastewater sampling and sampling small systems.
Read More